6061 T651 Aluminum Plate Case: Polish Mold Base Maker Halves Machining Allowance and Lead Time

November 19, 2026
Latest company case about 6061 T651 Aluminum Plate Case: Polish Mold Base Maker Halves Machining Allowance and Lead Time

Case Overview

This case covers a mold base and injection mold builder in Poland supplying automotive and appliance tooling. The shop replaced commercial 6061 plate with stress relieved 6061 T651 tooling plate, flat, UT tested and documented to EN 10204 3.1.

ItemDetail
CustomerMold base and injection mold builder in Poland, automotive and appliance tooling
ApplicationMold base plates, cavity blocks, bolster plates, fixture bases
Product6061 T651 stress relieved tooling plate, 6 to 200 mm, cut to size

The Challenge

  • Plate arrived out of flat. Commercial 6061 sheet carried bow and twist, so the shop faced off 3 to 5 mm per side to reach parallelism, turning purchased material into chips.
  • Porosity found after polishing. Without an ultrasonic report, internal porosity surfaced at final polishing, scrapping a cavity block after days of milling.
  • Documentation gaps. Automotive customers required EN 10204 3.1 certificates traceable to a heat number; stockist paperwork stopped at a generic mill certificate.
  • Long mill lead times. European mill deliveries ran 6 to 8 weeks, pushing mold trials past PPAP dates.

The Solution: Stress Relieved 6061 T651, Flat and Documented

Plates are thermally stress relieved so flatness holds after the base is cut and milled, supplied saw cut with deburred edges or machined to plus or minus 0.05 mm against a drawing.

GradeSizeSupply formWhere used
6061 T651 tooling plate6 to 200 mm, up to 6000 mmStress relieved, flatness 3 mm per meter, UT testedMold base and bolster plates
6061 T651 machined10 to 150 mmCNC milled, drilled, tapped, burr free, plus or minus 0.05 mmCavity blocks, fixture bases

Specification Highlights

PropertyValue
Alloy and temper6061 T651 / T6, EN AW 6061 equivalent
MechanicalYield 276 MPa min, tensile 310 to 340 MPa, elongation 10% min, 95 HB
Flatness3 mm per meter after stress relief, 2 mm per meter on machined plate
Internal qualityUltrasonic inspection, no porosity or inclusions accepted
DocumentsEN 10204 3.1 MTC with heat number, UT and dimensional reports, RoHS

Results After Two Supply Cycles

MetricBeforeAfterChange
Allowance per face3 to 5 mm1 to 1.5 mm60% less material
Facing hours per baseBaselineDown 45%Faster release
Scrap from hidden porosityOccasional block lossZeroUT before machining
Lead time6 to 8 weeks18 to 30 daysAbout half

Why the Customer Chose Our Factory

Four suppliers were shortlisted: two European stockists, one trader and our mill. The decision turned on five points, none of them price alone.

  1. Sample plate proven on their own machine. Two 6061 T651 samples with UT reports arrived in nine days; the shop milled them, measured flatness and approved the material before issuing a purchase order.
  2. Documents offered before the order, not after. EN 10204 3.1 with heat number, UT and dimensional reports and RoHS were written into the offer, so the buyer could show the file to its automotive customer in advance.
  3. Numbers written into the quotation. Flatness, tolerance and stock lead time were quoted as commitments, letting the buyer compare offers line by line.
  4. Factory, not trader. Rolling, stress relief and cutting happen in one plant with 3000 tons monthly capacity and an in-house laboratory, so a re-cut or a repeat order does not wait for a third party.
  5. Inspection and payment flexibility. SGS, BV or TUV inspection before shipment was accepted, and T/T, L/C, D/P and O/A terms let the buyer keep its own cash flow plan.
"We buy flatness and a certificate, not just kilos of aluminum. Since the switch we machine one millimetre instead of four, and no cavity block has been lost to porosity."
Tooling Manager, mold base builder in Poland

Talk to Us About Your Mold Base

We supply 6061 T651 and 6082 T6 stress relieved tooling plate, 6 to 200 mm, cut to size or machined to drawing, with UT reports and EN 10204 3.1 documents, shipped EU-wide.

Request a mold base plate quotation: send your drawing and flatness requirement